GRN MNSTR Antik AR1 Tornado Skates - Custom

$1,239.00

This product is for a custom coloured AR1 Tornado skate. Please note: even though you are paying for these custom skates now, allow 6-8 weeks for them to be made up and sent to you. Custom Antiks are not returnable so double check your size and other options before you order.

The AR1 boot features high cut, full-grain leather uppers for added ankle support and secure fit, Redesigned fully enclosed, contoured padded suede tongue, All new ‘Ergo-Form’ last for a more anatomical fit, and to reduce toe pinch, All new open toe design for better fit and comfort, Italian made ‘Harmony’ microfibre liner for more comfort and breathability, Heat moldable counters on both sides of the boot, Lace loops at the back of heel for added fit and security, Redesigned achilles area, Integrated shock absorbing foam heel, Contoured heel cup for secure fit and reduced lift, Full-grain leather outsole, stitched for durability, Redesigned Antik ‘A’ panels, Molded, padded heel insoles for maximum cushioning and it's 15% lighter than the AR1 predecessor.

Included in the custom package are:
Bearings: Moto deluxe bearings
Toe stops: GRN MNSTR Gumball toe stops (your choice of standard or short stem - record your choice in the downloaded form below)
Wheels: GRN MNSTR Reckless evader/Ikon XE (record colour of wheel in the downloaded form below)
Plate: Powerdyne Reactor pro series

To choose custom colours, boot size, boot width, wheel colour and stopper stem length, please download the Grn Mnstr form at this link, Antik form here. The form is the US version so just ignore the time frame and price.

Fill it in and either email it to: suziephedrine@sydneyderbyskates.com or snail mail it to:
Sydney Derby Skates
PO Box 108
Wentworth Falls
NSW 2782
And we will order your custom boots for you.

Click the "size charts" link for help with skate sizes.

Please don't assume that if you wear a size in one brand that the sizing will be the same in another brand as they do differ. In fact, sizing differs between brands with different skates. Please check the size charts.

Heat molding instructions:
Depending on how you want your boots to fit, there are a few options for heat molding the counters and toe area.
Option 1: hair dryer or heat gun
This option is for the individual problem areas (toes, arch, outer foot), and lets you mold one section at a time. Keep the gun/dryer at approx 6-8 inches away from boot, moving in a circular pattern. This should take about 3 min with the heat gun (6 to 7 min with hairdryer). Once the material is pliable, use your hands to push out the problem spot, and hold until cool. This process can be repeated as many times as needed. Note:Hairdryer will take more time to heat molding material.
Option 2: Oven
This option allows you to mold all three spots at once. Mold one boot at a time. Pre-heat oven to lowest setting (79-93 degrees depending on type of oven, DO NOT EXCEED 93 DEGREES OR TIME IN OVEN). Remove sock liner/foot bed, laces, toe stops, wheels and bearings (cushions can be left on). Place boot/skate in oven, on rack or cookie sheet for 3 minutes. Remove boot (Careful, boot will be HOT). Insert sock liner/foot bed, place foot in boot and lace up (be sure to wear the socks you tend to skate in the most). Stand up in boots and wait until cool. If you have a specific hot spot, use your hands to push the spot out or in for the desired fit. This process can be repeated as many times as needed.

Add to Cart:

  • Shipping Weight: 4kg
  • Manufactured by: Grn Mnstr Rollersports


This product was added to our catalog on Friday 11 September, 2015.

Copyright © 2017 Sydney Derby Skates.